What did you do to your Kia Stinger today?

[Gtecko]

Installed 3D printed snorkels from forum member Rakker and installed ATQ subframe bushings.

Where is the picture ?!?
I really like what he has done for those "big mouth"

 

[nhcowboy28]

Good luck with that. I dropped a socket when installing the rear sway. Never to be seen again even with an extended hunt with the car on a hoist.

10mm

 

[cncBilly]

Have you picked up any extraneous rattling noise from the rear?

No. It’s wedged good in there somewhere

 

[westcoastGT]

Have you picked up any extraneous rattling noise from the rear?

..................only from empty beer cans ................

 

[cncBilly]

10mm

No I believe it was a 14. The forward one on the rears left side by the fuel lines. Sounded like it dropped a couple inches but it just vanished. That’s went the decision was made to take the damn thing to my man with the hoist and pay him to tighten the prick up.

 

[cncBilly]

..................only from empty beer cans ................

Ya half mine half yours.

 

[General_Vodka]

Apron is painted. Looks pretty good, that area is going to be all covered by the JT intake boxes anyways. Now if only the JTs will arrive soon....

 

[General_Vodka]

Bonnet lift activated and windscreen cracked so a bit more than a small front hit......expensive!

Would not have been totaled if it was a small hit lol. $700 for the windshield, all because of the special HUD film.

 

[Snowwhite]

Got ARK GT-Fs installed. car rides fantastic and doesn't look like i slammed it

 

[General_Vodka]

The circle is complete. Sedan (Mazda), coupe (G37), wagon (TSX) and sportback. Stinger still looks the best out of the 4 lol.

 

[Spaceme17]

Where is the picture ?!?
I really like what he has done for those "big mouth"

Here you go:

 

[cncBilly]

The circle is complete. Sedan (Mazda), coupe (G37), wagon (TSX) and sportback. Stinger still looks the best out of the 4 lol. View attachment 45943

Even with the sore nose!

 

[bcleezy05]

Finally had some time to play with the wheels. VHT Gloss Black.

View attachment 45603View attachment 45604

Looking good, did you sand and apply primer or did you just spray the VHT on?

 

[General_Vodka]

Found this button

 

[cncBilly]

Found this button View attachment 45967

Sadly my layman eyes will need a bit more verbiage

 

[General_Vodka]

Sadly my layman eyes will need a bit more verbiage

Sensor plug tip was broken, and I got intake valve solenoid error code. Figured this thing was it and bought a new one. Here it is installed

 

[codizzzy]

10,000 mile-a-versary! Celebrated by installing the ADD 3.3 catch can, JB4 with bluetooth, vanity covers, JT merge pipe, and the JT intakes with clear airbox lids!

 

[General_Vodka]

10,000 mile-a-versary! Celebrated by installing the ADD 3.3 catch can, JB4 with bluetooth, vanity covers, JT merge pipe, and the JT intakes with clear airbox lids!View attachment 45969

Did you already have your JTs? I am still waiting on mine

 

[codizzzy]

Did you already have your JTs? I am still waiting on mine

I ordered them a couple of weeks before the group order started up and got them yesterday. Shipping only took 3 days.

 

[mhal8876]

10,000 mile-a-versary! Celebrated by installing the ADD 3.3 catch can, JB4 with bluetooth, vanity covers, JT merge pipe, and the JT intakes with clear airbox lids!View attachment 45969

what is that for the little red air filter that exposed? Is that useful? looks like easy mod too.