Lozic ECU + TCU + AWD Tune

[SneakerB]

You will build boost to .5bar and RPM will hold at around 2.2k the same as factory launch control (holding the pedal 100%). So you will launch with boost built but the TCU torque limits remain. That's why the launch isn't as strong as when having the TCU installed.

dahm i figured rpms would shoot higher than that

 

[kylepark1230]

i don’t have wmi I was just using map 6 for logging. Should I use map 0? I’ll get a better run in the future. Thanks for the tip.

you need to disable fuel control wires! and none of those are good enough runs to say whether its running good or not! do a third to fourth gear pull wide open throttle and why are you running map 6? do you have wmi?

 

[SneakerB]

i don’t have wmi I was just using map 6 for logging. Should I use map 0? I’ll get a better run in the future. Thanks for the tip.

Yea run map0

 

[kylepark1230]

you need to disable fuel control wires! and none of those are good enough runs to say whether its running good or not! do a third to fourth gear pull wide open throttle and why are you running map 6? do you have wmi?

What does disabling the fuel control wires do btw? And what was happening while I did have them on?

 

[SneakerB]

What does disabling the fuel control wires do btw? And what was happening while I did have them on?

You want the exu tune to control your fuel not the jb4!

 

[kylepark1230]

You want the exu tune to control your fuel not the jb4!

Do I want to do anything else with the jb4? The fuel control wires are the red posi tap right?

 

[SneakerB]

Do I want to do anything else with the jb4? The fuel control wires are the red posi tap right?

Yes there the two posi taps but you can leave them on, just disable it it in user settings on the jb4, you could also disable ewg wires and jb4 saftey settings to see how it runs

 

[Pearly]

Yes there the two posi taps but you can leave them on, just disable it it in user settings on the jb4, you could also disable ewg wires and jb4 saftey settings to see how it runs

I may be minority.. but when I move to map0 those automatically disable.

 

[SneakerB]

I may be minority.. but when I move to map0 those automatically disable.

They shouldnt you sure those bits are green in the user adjustment menu?

 

[Pearly]

They shouldnt you sure those bits are green in the user adjustment menu?

100%. I did logs in map6 and then map0 and watched WGDC and fuel trims. In Map0 it’s all ECU. Map6 then Jb4 took over. And didn’t change the bits. Map0 is Jb4 disabled period for me. Just logging

 

[G70LEbyAdoom]

100%. I did logs in map6 and then map0 and watched WGDC and fuel trims. In Map0 it’s all ECU. Map6 then Jb4 took over. And didn’t change the bits. Map0 is Jb4 disabled period for me. Just logging

This is how it is suppose to behave. it it doesn't, then something is wrong.

 

[SneakerB]

Huh

100%. I did logs in map6 and then map0 and watched WGDC and fuel trims. In Map0 it’s all ECU. Map6 then Jb4 took over. And didn’t change the bits. Map0 is Jb4 disabled period for me. Just logging

huh thats weird my wastegat

This is how it is suppose to behave. it it doesn't, then something is wrong.

i could of sworn you have to turn of ewg wires either way cause it only shows up on logs when turned on.

 

[G70LEbyAdoom]

Huh

huh thats weird my wastegat

i could of sworn you have to turn of ewg wires either way cause it only shows up on logs when turned on.

Nope, Map 0 is OFF OFF, like nothing is there.

 

[Yves998]

Funny how I was assuming DA means nothing for turbo car while 700 DA lower gives me 0.2s quicker 0-60.

 

[StingertimeNC]

Strong times either way but yes, that DA makes a big difference.

 

[kylepark1230]

I hope these are better runs

Yes there the two posi taps but you can leave them on, just disable it it in user settings on the jb4, you could also disable ewg wires and jb4 saftey settings to see how it runs

 

[SneakerB]

I hope these are better runs

yea id send that to lozic... your pulling 9 degrees of timing at one point.. what fuel are you running?

 

[SneakerB]

I hope these are better runs

you also dont need to post the pictures only the csv file!

 

[Yves998]

I hope these are better runs

That’s too much timing pull and you need retune asap if you’re already running the best fuel you can get already.

 

[kylepark1230]

I’m running 93 octane at the moment. Can you tell me what 9 degrees of timing means?

yea id send that to lozic... your pulling 9 degrees of timing at one point.. what fuel are you running?