robz32
Texas Stinger Swarm
Not sure where you saw that. I revisited the listing and I can not find anywhere where it says that it will not ship to the US.
How to install OEM Wireless Charger on your Stinger
- Thread starter robz32
- Start date
Not sure where you saw that. I revisited the listing and I can not find anywhere where it says that it will not ship to the US.
TuscaniCustoms
Active Member
Just listed it console kit+wireless charger OEM Wireless Charging Pad+Center Console with Cup Holder kia stinger
jongkihong
Active Member
______________________________
Reignman98115
Member
- Joined
- Oct 18, 2017
- Messages
- 52
- Reaction score
- 10
- Points
- 8
Yeah we found out its because i live in Hawaii but he fixed it to ship there
Hey @robz32, just a question regarding the climate control. Driving home getting lunch, I figured I'd try to at least loosen, if not remove, the climate control in preparation for my installation tonight...but how hard did you have to press?? That son of a bitch doesn't even budge with using your method. I feel like the entire console is going to rip out with how hard I was pressing, might you have used some kind of a tool or have a slightly different suggestion for it? Seems impossible!
From interior to exterior to high performance - everything you need for your Stinger awaits you...
robz32
Texas Stinger Swarm
@Berzerker Yes, that SOB is one tough bastid. In hindsight If I were to do it again I would just leave it in there and not bother with it. The harness that plugs in to it, has enough slack to slide the whole console backwards. You will be able to access the plug once the console is slid backwards.
Let me know if you need additional help. I'll try to answer as quick as possible.
Let me know if you need additional help. I'll try to answer as quick as possible.
Last edited:
Does the part the climate control attaches into move with the console? I'm gonna try not removing it first, I'll see how it goes.
Last edited by a moderator:
robz32
Texas Stinger Swarm
Correct. The climate control panel is attached to a back plate that is attached to the glossy black trim and it comes out with the console.
And we're swapped! Big thanks to @robz32 for the instructions and help and @jongkihong for the *insanely* fast shipping!
Finished product:
Some notes about the install:
- As discussed in the previous 2 posts, I didn't actually have to remove the climate control from the holder! At the stage of unclipping the glossy black plastic guard, the entire thing just slides out, and comes out as one unit. Should make this a lot easier for people in the future.
- Those clips are a *bitch* to get out. The side beauty panels actually have 5 total clips and a slide guard, so I had really no choice but to just unclip as many as I could get to (basically the 3 that were circled in the original post) then just slide it towards the seat and pull. They're actually pretty sturdy, so nothing broke.
- For some reason, the passenger side bolt in the center console cubby under the little mat was *ridiculously* hard to unbolt. After I put everything back together, I noticed a slight rattling and realized that, even though it was incredibly hard to bolt that back in, it still wasn't completely in! Just had to put a lot of muscle in it and eventually got it flush, just remember to tighten everything down!
- Don't forget all your screws! I almost forgot the two philips head screws holding the glossy black trim down before putting back in the center console.
All-in-all, I'm super happy with the swap. Everything is a lot cleaner, and now, even if your phone doesn't support wireless charging, you have a dedicated slot for your phone to sit.
In terms of fit, the largest phone I own, the Pixel 2 XL, fits no problem with nothing connected, but doesn't fit that well with the USB connected. Smaller phones like the S9 should fit better with a USB connected.
Also, even though the cup holders are smaller, they have no problem fitting a large cup from Wendy's in both holders! The back one is a bit tighter of a fit, but it does hold it!
Here's some pics:
Finished product:
Some notes about the install:
- As discussed in the previous 2 posts, I didn't actually have to remove the climate control from the holder! At the stage of unclipping the glossy black plastic guard, the entire thing just slides out, and comes out as one unit. Should make this a lot easier for people in the future.
- Those clips are a *bitch* to get out. The side beauty panels actually have 5 total clips and a slide guard, so I had really no choice but to just unclip as many as I could get to (basically the 3 that were circled in the original post) then just slide it towards the seat and pull. They're actually pretty sturdy, so nothing broke.
- For some reason, the passenger side bolt in the center console cubby under the little mat was *ridiculously* hard to unbolt. After I put everything back together, I noticed a slight rattling and realized that, even though it was incredibly hard to bolt that back in, it still wasn't completely in! Just had to put a lot of muscle in it and eventually got it flush, just remember to tighten everything down!
- Don't forget all your screws! I almost forgot the two philips head screws holding the glossy black trim down before putting back in the center console.
All-in-all, I'm super happy with the swap. Everything is a lot cleaner, and now, even if your phone doesn't support wireless charging, you have a dedicated slot for your phone to sit.
In terms of fit, the largest phone I own, the Pixel 2 XL, fits no problem with nothing connected, but doesn't fit that well with the USB connected. Smaller phones like the S9 should fit better with a USB connected.
Also, even though the cup holders are smaller, they have no problem fitting a large cup from Wendy's in both holders! The back one is a bit tighter of a fit, but it does hold it!
Here's some pics:
Last edited:
robz32
Texas Stinger Swarm
WOOOHOOO!!....looks like it came pretyy nice!!...Congratulations! 
That is how our cars should have come from the factory.
That is how our cars should have come from the factory.
______________________________
From interior to exterior to high performance - everything you need for your Stinger awaits you...
Thanks.WOOOHOOO!!....looks like it came pretyy nice!!...Congratulations!
That is how our cars should have come from the factory.
So I think I'm now the second person to do this swap? Hopefully we get some more!
robz32
Texas Stinger Swarm
As far as I know, yes you are the second one.
Reignman98115
Member
- Joined
- Oct 18, 2017
- Messages
- 52
- Reaction score
- 10
- Points
- 8
Please do a video DIY if u can. I would love it. Thanks
jongkihong
Active Member
Congratulations on successful installation ...
Club members should contact me before purchasing the product ...
It gives us a discount on the product and date of arrival.
Club members should contact me before purchasing the product ...
It gives us a discount on the product and date of arrival.
From interior to exterior to high performance - everything you need for your Stinger awaits you...
Killa200
Active Member
- Joined
- Mar 15, 2018
- Messages
- 129
- Reaction score
- 114
- Points
- 43
Did I say Wednesday?
@Reignman98115 i don't have a real good way honestly to get any video footage besides me trying to hold my phone while I'm also taking things apart, but I don't mind taking pictures of anything that you needed clarification on that robz32 didn't cover.
@Reignman98115 i don't have a real good way honestly to get any video footage besides me trying to hold my phone while I'm also taking things apart, but I don't mind taking pictures of anything that you needed clarification on that robz32 didn't cover.
______________________________
Honestly, the pictures do a really good job at showing you what needs to be done. Once you get past removing the center console from the SGT&Me video, there aren't that many steps between getting to that and removing the part. Just understand the reference and keep your screws organized, and you'll understand the logical steps as you go.
TuscaniCustoms
Active Member
Customs took really long to release your console Cody. Now lets see some install pictures 
Reignman98115
Member
- Joined
- Oct 18, 2017
- Messages
- 52
- Reaction score
- 10
- Points
- 8
Question. So looks like I have a bigger task at hand to install the wireless charge pad unit. I have the regular shifter (non shift by wire), and I'm wondering by looking at the pics I posted, if I can get this son of a gun out? Any suggestions on how to remove it? Or can I get the charge pad in without the removal of the shifter? I know it would be easier without it but is it possible? Seems like I might be able to move the console a little bit back but would I have enough room to squeeze the non charge pad out and the new one in? Please if anyone can help me. Or am I out of luck? The good news is that I at least can get the cup holder cover console in. Note: in the first pic you will notice a bolt way back under the tray. From interior to exterior to high performance - everything you need for your Stinger awaits you...
