JB4 map0 and map1 logs 80%throttle Can anyone take a look at them?

[terry390]

80% throttle
91 octane
bms intake
6ix oil catch can
Ark secondary+Mbrp
JB4+bluetooth+fuel wire
Im new to JB4, I want to make sure the stinger is doing fine before I go on map 2 and beyond.

How do I know if my fuel wires are connected correctly and working?


Thanks in advance.

 

[rpoffen]

You should set the JB4 to only log when throttle is at 80 or above, eliminates the extra uninteresting stuff in the log.
Also, try to get a full throttle run starting at about 30mph up to 80.
In the parts where you were seeing boost, I see a few timing corrections, but not bad. Try map 2 and post that log.

 

[terry390]

You should set the JB4 to only log when throttle is at 80 or above, eliminates the extra uninteresting stuff in the log.
Also, try to get a full throttle run starting at about 30mph up to 80.
In the parts where you were seeing boost, I see a few timing corrections, but not bad. Try map 2 and post that log.

thx man.
I will do my logs again and try to avoid any unnecessary logs with 30mph to 80 pulls.

 

[rpoffen]

thx man.
I will do my logs again and try to avoid any unnecessary logs with 30mph to 80 pulls.

Go into the JB4 app, click on "Settings", then under Advanced "JB4 Tuning/App Configs" -> "App Settings" -> "Logging Settings" -> "WOT Start Threshold (Pedal)" and select 80%.
Then it will automatically log when you punch it, no need to start logging manually, just connect the app when you start the car.

 

[terry390]

Go into the JB4 app, click on "Settings", then under Advanced "JB4 Tuning/App Configs" -> "App Settings" -> "Logging Settings" -> "WOT Start Threshold (Pedal)" and select 80%.
Then it will automatically log when you punch it, no need to start logging manually, just connect the app when you start the car.

i actually did this setting and I still manually turning the log on and off. lol

 

[rpoffen]

i actually did this setting and I still manually turning the log on and off. lol

I see. I used to do that too. LOL

 

[terry390]

Go into the JB4 app, click on "Settings", then under Advanced "JB4 Tuning/App Configs" -> "App Settings" -> "Logging Settings" -> "WOT Start Threshold (Pedal)" and select 80%.
Then it will automatically log when you punch it, no need to start logging manually, just connect the app when you start the car.

I just added a new log for map1. will do map2 next time. however im still using stock plugs.

 

[rpoffen]

I just added a new log for map1. will do map2 next time. however im still using stock plugs.

Definitely need to get those swapped out.
Stock plugs won’t last long.
I recommend HKS. More pricey, but they last longer.

 

[cncBilly]

I just added a new log for map1. will do map2 next time. however im still using stock plugs.

That one looks pretty good. A couple pulls in #4 at higher boost but not concerning. Do as @rpoffen says and GET THOSE PLUGS CHANGED ASAP!

 

[terry390]

That one looks pretty good. A couple pulls in #4 at higher boost but not concerning. Do as @rpoffen says and GET THOSE PLUGS CHANGED ASAP!

Thanks man. will put HKS plugs in soon.

 

[rpoffen]

Thanks man. will put HKS plugs in soon.

Smart

 

[rpoffen]

Thanks man. will put HKS plugs in soon.

Drop an email to k8 stinger store, tell him you are a new “modder”, he might give you a discount.

 

[terry390]

Drop an email to k8 stinger store, tell him you are a new “modder”, he might give you a discount.

will do. thank you for the advice. They r currently out of stock

 

[rpoffen]

will do. thank you for the advice. They r currently out of stock

Well that’s not good.
Be careful of eBay or Amazon, I have heard that there are fake ones being sold cheap.

 

[rpoffen]

will do. thank you for the advice. They r currently out of stock

Kdm warehouse also sold out.
What the heck, must be stuck on a boat somewhere.