Took a 800+ mile road trip. Ride much improved with very slight increase in road noise. Tire wear doesn’t seem to be impacted yet. Tire pressure only reached 33 PSI so that tells me tire temperature not adversely affected. I’m leaving cold pressure set to 30 PSI for now.
Sorry if this is a bit abrupt but those tyre pressures are way too low. Had a stinger for 70 months now, for RWD you'll need 36f & 38r as recommended . A lot run a couple of lbs more.
Sorry if this is a bit abrupt but those tyre pressures are way too low. Had a stinger for 70 months now, for RWD you'll need 36f & 38r as recommended . A lot run a couple of lbs more.
Took a 800+ mile road trip. Ride much improved with very slight increase in road noise. Tire wear doesn’t seem to be impacted yet. Tire pressure only reached 33 PSI so that tells me tire temperature not adversely affected. I’m leaving cold pressure set to 30 PSI for now.
when I change wheels / tires for the season I have the psi set to 40 cold. over the next months this drops, for instance last spring I did this, and currently when I start up and the tpms comes on it will show 33 psi or a lb. or 2 more, and warm up to about 36 psi. next spring when I put these michelins back on I will have them raised to 40 psi cold again. in the middle of winter the 40 psi cold hovers right around there when warmed up. in summer, the 40 psi cold warms up to mid-40s psi, and on a real scorcher might hit 48 psi. yes, this is ten lbs. higher than recommended on the door card. but I like to corner fast and tend to wear out my outer edges first in front. so the higher psi offsets that tendency.
The mail i got is Kia inflate them from the factory like that for the trip by ship then to holding yard and then the dealer. The dealer in his pre sales inspection is meant to lower the pressures to the recommended level.
Quite pathetic they skip this as you're paying for a deliver cost.
Not odd for staggered, that is standard. Comparatively, 18" wheels squared on the 2.0L AWD are supposed to be 36 psi front 39 psi rear. our GT1 AWD also requires 38 front 36 rear.
Not odd for staggered, that is standard. Comparatively, 18" wheels squared on the 2.0L AWD are supposed to be 36 psi front 39 psi rear. our GT1 AWD also requires 38 front 36 rear.
Higher rear than front is pretty surprising. I could see the 4cyl reducing the higher front pressure (from the 6cyl) to match the rear due to a little less weight up front, but going from 2psi higher up front to 3psi lower seems like it would give the car much more tendency toward oversteer.
But maybe the reduced power or other suspension differences make this moot. Kind of surprised they didn't engineer it to be same front & rear pressure since so many people will do that, on the rare occasion they do check pressure.
Higher rear than front is pretty surprising. I could see the 4cyl reducing the higher front pressure (from the 6cyl) to match the rear due to a little less weight up front, but going from 2psi higher up front to 3psi lower seems like it would give the car much more tendency toward oversteer.
But maybe the reduced power or other suspension differences make this moot. Kind of surprised they didn't engineer it to be same front & rear pressure since so many people will do that, on the rare occasion they do check pressure.
The psi range for all trims of Stingers throughout production is 36-39 psi. We are not talking about a significant difference. I like to play with my psi, and TPMS system, knowing that on my cars the indicated TPMS psi is 4-5 lbs. lower than actual. This I determined by triangulating with two handheld tire gauges, that are within 1 psi of each other. What I do is keep the cold psi by tire gauge as close to the door card recommendations as possible, when I adjust my tire pressures. When I drive I expect to see the cold psi on the TPMS showing c. 4 psi lower than what I saw on the handheld gauge.
I would be very curious what the differences in temperatures actually are.
I never saw any differences in temperature front versus rear when I was running staggered fitment.
Currently I am running square setup, and the temperatures stay within 1°C of each other (when at the same pressure cold) after driving at least 10 minutes.
You can check that with a $10 OBD2 reader and a free app.