Hey! I see you! Please take two seconds to sign up! We'd love to have you as a member of our Kia Stinger club. You have nothing to lose and so much to gain... :)

3.3TT BMS Stinger Tial BOV Kit Teaser Video

Discussion in 'Engine, Drivetrain, and Exhaust Discussion' started by Terry@BMS, Aug 9, 2018.

  1. Terry@BMS

    Terry@BMS United States 1000 Posts Club! Authorized Vendor

    1,309
    840
    118
    • Like Like x 4
  2. RandallK

    RandallK United States Active Member

    257
    195
    43
    Location:
    St. Louis Missouri
    So bad ass.. I can’t wait!!!
     
  3. MekstingerGT

    MekstingerGT United States Active Member

    212
    86
    28
    Nice! What's the benefit of using 1 or 2 bov?
     
    • Like Like x 1
  4. NYdito

    NYdito United States Active Member

    464
    218
    43
    Location:
    Bronx NY
    Nice!!
     
  5. KLR STINGER

    KLR STINGER Canada Active Member

    427
    306
    68
    No specific reason to use 1 vs 2 other than venting capacity. The stinger uses 2 probably because they already had one designed for the elantra sport and was easier/cheaper to add a second one for the needed capacity of the 3.3, than design and spec a new one. A 50MM Hi flow BOV ( tial/turbosmart/etc) should provide enough flow to vent 1000+ hp
     
    Last edited: Aug 10, 2018
  6. Kamauxx

    Kamauxx United States 2500 Posts Club!

    3,663
    1,419
    118
    Does this actually (REALLY) do anything other than make noise?
     
    • Agree Agree x 1
  7. DaBears4Lyfe

    DaBears4Lyfe United States 1000 Posts Club!

    1,203
    328
    88
    Location:
    Chicagoland
    Nice Terry! If you need some additional reviews and testers when you finish the product I would gladly help out :D
     
  8. KLR STINGER

    KLR STINGER Canada Active Member

    427
    306
    68
    BOV's/re-circulation valves are required to eliminate damaging compressor surge on throttle closure under boost. OEM plastic recirc valves are notorious for leaking boost, failing over time and increased boost level. A Fast responding BOV with a lightweight piston design also improves boost recovery between shifts, and can also help at launch when transitioning from vacuum to boost. This particular one will help a tuned car in the areas above, but for a stock car it's not necessary
     
    • Informative Informative x 3
    • Like Like x 2
  9. Kamauxx

    Kamauxx United States 2500 Posts Club!

    3,663
    1,419
    118
    Thanks for the info!
     
  10. MekstingerGT

    MekstingerGT United States Active Member

    212
    86
    28
    Is this for the adaptor flang or the whole setup?
     
  11. Terry@BMS

    Terry@BMS United States 1000 Posts Club! Authorized Vendor

    1,309
    840
    118
    • Like Like x 3
    • Informative Informative x 1
  12. robz32

    robz32 United States 1000 Posts Club! Staff Member Moderator Texas Stinger Swarm

    1,915
    821
    118
    Location:
    Houston, TX
    Not sure how I missed this post. But that looks great @Terry@BMS Thanks for developing this part. Looking forward to the release.
     
  13. DiabloStinger

    DiabloStinger United States Stinger Enthusiast

    816
    215
    43
    Location:
    Gilbert, AZ
    Any further information on this single valve design? I know a few people that would snap this up in a heartbeat.
     
  14. Oryan

    Oryan United States Active Member

    124
    31
    28
    Since you were down there looking at the BOVs... do you see any reason or benefit to upgrading the stock hot side IC piping?
     
  15. jatleson

    jatleson United States Member

    81
    16
    8
    These are a lot quieter than the HKS kits I've seen (a good thing). Have you considered molding the DV caps onto the flange? Would clean up the look and prevent than tubes from flopping around.
     
Draft saved Draft deleted

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.